Arista EOS - Interfaces & MLAG

EOS data-centre switching: MLAG, VXLAN, BGP and config sessions.

Arista Requires SmartCom Revisited 1.0.0 or newer

by Nathan Kirk · 71 downloads · MIT licence · revision 1 · published 14 Aug 2026

This bundle can change or destroy device state

Reboots or reloads the device (3 steps) — Restarts the device. Any session on it drops, and anything not saved is lost.
Shuts down an interface (1 step) — Administratively disables an interface. If it is the interface you are connected over, you lose the session.
Writes configuration to persistent storage (1 step) — Makes the current configuration survive a reboot. Intended, usually — but it is not a read-only button.

Show exactly which steps matched

Shut Down Interface — Shuts down an interface (steps[3], sent text)
```
shutdown
```
Save Running Config — Writes configuration to persistent storage (steps[0], sent text)
```
write memory
```
Reload Device — Reboots or reloads the device (steps[1], sent text)
```
reload now
```
Reload in Minutes — Reboots or reloads the device (steps[1], sent text)
```
reload in {{MINUTES}}
```
Cancel Scheduled Reload — Reboots or reloads the device (steps[0], sent text)
```
reload cancel
```

Flagged automatically by matching command text. It is a prompt to read the script, not a verdict — plenty of legitimate buttons reboot things on purpose.

3 sets, 122 buttons, 185 steps · 137.2 KB

File format version 1 · exported by Smartcom Revisited

Download .buttons.json

SHA-256 19573f13902d151001b48e885b519a8c9f361d543fd370bc7e8b77a1d9f3639a

You get the exact file the uploader submitted, byte for byte — that checksum is what sha256sum will print. Import it from the button panel in SmartCom Revisited.

About this set

Arista EOS for leaf-and-spine work: interface and MLAG health, VXLAN and EVPN state, BGP underlay and overlay, plus config sessions so a change can be staged, reviewed and committed or abandoned.

Every button, in full

Exactly what gets sent

This is the complete script of the file below — nothing is summarised or hidden. Read it before you download it, the same way you would read a script someone emailed you.

Arista EOS - Interfaces & MLAG

36 buttons

Interface state, port-channels, MLAG health and VLANs.

Interface Status

Run: show interfaces status

1 step

Send
```
show interfaces status
```
Sends Enter afterwards.

Interface Status Connected

Run: show interfaces status connected

1 step

Send
```
show interfaces status connected
```
Sends Enter afterwards.

Interface Status Errdisabled

Run: show interfaces status errdisabled

1 step

Send
```
show interfaces status errdisabled
```
Sends Enter afterwards.

Interface Detail

Run: show interfaces {{IFACE}}

1 step · 1 input

Send
```
show interfaces {{IFACE}}
```
Sends Enter afterwards.

Interface Counters

Run: show interfaces counters

1 step

Send
```
show interfaces counters
```
Sends Enter afterwards.

Interface Error Counters

Run: show interfaces counters errors

1 step

Send
```
show interfaces counters errors
```
Sends Enter afterwards.

Interface Discards

Run: show interfaces counters discards

1 step

Send
```
show interfaces counters discards
```
Sends Enter afterwards.

Interface Rates

Run: show interfaces counters rates

1 step

Send
```
show interfaces counters rates
```
Sends Enter afterwards.

Interface Descriptions

Run: show interfaces description

1 step

Send
```
show interfaces description
```
Sends Enter afterwards.

Transceiver Detail

Run: show interfaces {{IFACE}} transceiver detail

1 step · 1 input

Send

show interfaces {{IFACE}} transceiver detail

Sends Enter afterwards.

Transceiver Health

Run: show interfaces transceiver

1 step

Send
```
show interfaces transceiver
```
Sends Enter afterwards.

Port-Channel Summary

Run: show port-channel summary

1 step

Send
```
show port-channel summary
```
Sends Enter afterwards.

Port-Channel Detail

Run: show port-channel {{LAG}} detailed

1 step · 1 input

Send
```
show port-channel {{LAG}} detailed
```
Sends Enter afterwards.

LACP Neighbours

Run: show lacp neighbor

1 step

Send
```
show lacp neighbor
```
Sends Enter afterwards.

LACP Counters

Run: show lacp counters

1 step

Send
```
show lacp counters
```
Sends Enter afterwards.

MLAG Status

Run: show mlag

1 step

Send
```
show mlag
```
Sends Enter afterwards.

MLAG Detail

Run: show mlag detail

1 step

Send
```
show mlag detail
```
Sends Enter afterwards.

MLAG Interfaces

Run: show mlag interfaces

1 step

Send
```
show mlag interfaces
```
Sends Enter afterwards.

MLAG Config Sanity

Run: show mlag config-sanity

1 step

Send
```
show mlag config-sanity
```
Sends Enter afterwards.

VLAN Summary

Run: show vlan

1 step

Send
```
show vlan
```
Sends Enter afterwards.

VLAN Detail

Run: show vlan {{VLAN}}

1 step · 1 input

Send
```
show vlan {{VLAN}}
```
Sends Enter afterwards.

MAC Address Table

Run: show mac address-table

1 step

Send
```
show mac address-table
```
Sends Enter afterwards.

Find MAC Address

Run: show mac address-table address {{MAC}}

1 step · 1 input

Send
```
show mac address-table address {{MAC}}
```
Sends Enter afterwards.

MAC Table Count

Run: show mac address-table count

1 step

Send
```
show mac address-table count
```
Sends Enter afterwards.

Spanning-Tree Summary

Run: show spanning-tree summary

1 step

Send
```
show spanning-tree summary
```
Sends Enter afterwards.

Spanning-Tree Detail

Run: show spanning-tree

1 step

Send
```
show spanning-tree
```
Sends Enter afterwards.

LLDP Neighbours

Run: show lldp neighbors

1 step

Send
```
show lldp neighbors
```
Sends Enter afterwards.

LLDP Detail

Run: show lldp neighbors detail

1 step

Send
```
show lldp neighbors detail
```
Sends Enter afterwards.

Set Interface Description

Run: configure ; interface {{IFACE}} ; description {{DESCRIPTION}} ; end

4 steps · asks for confirmation before it runs · 2 inputs

Send
```
configure
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
description {{DESCRIPTION}}
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Set Access VLAN

Run: configure ; interface {{IFACE}} ; switchport mode access ; switchport access vlan {{VLAN}} ; end

5 steps · asks for confirmation before it runs · 2 inputs

Send
```
configure
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
switchport mode access
```
Sends Enter afterwards.
Send
```
switchport access vlan {{VLAN}}
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Configure Trunk Port

Run: configure ; interface {{IFACE}} ; switchport mode trunk ; switchport trunk allowed vlan {{VLAN_LIST}} ; end

5 steps · asks for confirmation before it runs · 2 inputs

Send
```
configure
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
switchport mode trunk
```
Sends Enter afterwards.

Send

switchport trunk allowed vlan {{VLAN_LIST}}

Sends Enter afterwards.

Send
```
end
```
Sends Enter afterwards.

Create VLAN

Run: configure ; vlan {{VLAN}} ; name {{VLAN_NAME}} ; end

4 steps · asks for confirmation before it runs · 2 inputs

Send
```
configure
```
Sends Enter afterwards.
Send
```
vlan {{VLAN}}
```
Sends Enter afterwards.
Send
```
name {{VLAN_NAME}}
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Enable Interface

Run: configure ; interface {{IFACE}} ; no shutdown ; end

4 steps · asks for confirmation before it runs · 1 input

Send
```
configure
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
no shutdown
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Shut Down Interface

Run: configure ; interface {{IFACE}} ; shutdown ; end

5 steps · asks for confirmation before it runs · 1 input

Shuts down an interface

Confirm

Asks yes or no: “Shut down {{IFACE}}. Anything behind it loses its link immediately, and if it is an MLAG or uplink member the fabric reconverges. Continue?”

Answering no stops the script here.
Send
```
configure
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
shutdown
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Clear Interface Counters

Run: clear counters {{IFACE}}

2 steps · asks for confirmation before it runs · 1 input

Confirm

Asks yes or no: “Reset the counters on {{IFACE}}. The error history you are looking at is lost. Continue?”

Answering no stops the script here.
Send
```
clear counters {{IFACE}}
```
Sends Enter afterwards.

Reset Interface to Default

Run: configure ; default interface {{IFACE}} ; end

4 steps · asks for confirmation before it runs · 1 input

Confirm

Asks yes or no: “Wipe every setting on {{IFACE}} back to default, including its VLAN, channel-group and description. Continue?”

Answering no stops the script here.
Send
```
configure
```
Sends Enter afterwards.
Send
```
default interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Arista EOS - Routing, VXLAN & EVPN

39 buttons

Routing table, BGP underlay and overlay, VXLAN and VTEPs.

Routing Table

Run: show ip route

1 step

Send
```
show ip route
```
Sends Enter afterwards.

Route for Prefix

Run: show ip route {{PREFIX}}

1 step · 1 input

Send
```
show ip route {{PREFIX}}
```
Sends Enter afterwards.

Route Summary

Run: show ip route summary

1 step

Send
```
show ip route summary
```
Sends Enter afterwards.

Connected Routes

Run: show ip route connected

1 step

Send
```
show ip route connected
```
Sends Enter afterwards.

Static Routes

Run: show ip route static

1 step

Send
```
show ip route static
```
Sends Enter afterwards.

BGP Routes

Run: show ip route bgp

1 step

Send
```
show ip route bgp
```
Sends Enter afterwards.

Routes in VRF

Run: show ip route vrf {{VRF}}

1 step · 1 input

Send
```
show ip route vrf {{VRF}}
```
Sends Enter afterwards.

ARP Table

Run: show ip arp

1 step

Send
```
show ip arp
```
Sends Enter afterwards.

ARP for Host

Run: show ip arp {{IP}}

1 step · 1 input

Send
```
show ip arp {{IP}}
```
Sends Enter afterwards.

ARP Inspection

Run: show ip arp inspection statistics

1 step

Send
```
show ip arp inspection statistics
```
Sends Enter afterwards.

BGP Summary

Run: show ip bgp summary

1 step

Send
```
show ip bgp summary
```
Sends Enter afterwards.

BGP Neighbours

Run: show ip bgp neighbors

1 step

Send
```
show ip bgp neighbors
```
Sends Enter afterwards.

BGP Neighbour Detail

Run: show ip bgp neighbors {{PEER}}

1 step · 1 input

Send
```
show ip bgp neighbors {{PEER}}
```
Sends Enter afterwards.

BGP Routes Received

Run: show ip bgp neighbors {{PEER}} received-routes

1 step · 1 input

Send

show ip bgp neighbors {{PEER}} received-routes

Sends Enter afterwards.

BGP Routes Advertised

Run: show ip bgp neighbors {{PEER}} advertised-routes

1 step · 1 input

Send

show ip bgp neighbors {{PEER}} advertised-routes

Sends Enter afterwards.

BGP EVPN Summary

Run: show bgp evpn summary

1 step

Send
```
show bgp evpn summary
```
Sends Enter afterwards.

BGP EVPN Routes

Run: show bgp evpn

1 step

Send
```
show bgp evpn
```
Sends Enter afterwards.

BGP EVPN Route Type 2

Run: show bgp evpn route-type mac-ip

1 step

Send
```
show bgp evpn route-type mac-ip
```
Sends Enter afterwards.

BGP EVPN Route Type 5

Run: show bgp evpn route-type ip-prefix ipv4

1 step

Send
```
show bgp evpn route-type ip-prefix ipv4
```
Sends Enter afterwards.

OSPF Neighbours

Run: show ip ospf neighbor

1 step

Send
```
show ip ospf neighbor
```
Sends Enter afterwards.

OSPF Interfaces

Run: show ip ospf interface brief

1 step

Send
```
show ip ospf interface brief
```
Sends Enter afterwards.

VXLAN Configuration

Run: show interfaces vxlan 1

1 step

Send
```
show interfaces vxlan 1
```
Sends Enter afterwards.

VXLAN VTEP List

Run: show vxlan vtep

1 step

Send
```
show vxlan vtep
```
Sends Enter afterwards.

VXLAN VNI Mapping

Run: show vxlan vni

1 step

Send
```
show vxlan vni
```
Sends Enter afterwards.

VXLAN Address Table

Run: show vxlan address-table

1 step

Send
```
show vxlan address-table
```
Sends Enter afterwards.

VXLAN Flood List

Run: show vxlan flood vtep

1 step

Send
```
show vxlan flood vtep
```
Sends Enter afterwards.

VRF List

Run: show vrf

1 step

Send
```
show vrf
```
Sends Enter afterwards.

Ping Host

Run: ping {{HOST}} repeat {{COUNT}}

1 step · 2 inputs

Send
```
ping {{HOST}} repeat {{COUNT}}
```
Sends Enter afterwards.

Ping in VRF

Run: ping vrf {{VRF}} {{HOST}} repeat {{COUNT}}

1 step · 3 inputs

Send

ping vrf {{VRF}} {{HOST}} repeat {{COUNT}}

Sends Enter afterwards.

Ping from Source

Run: ping {{HOST}} source {{IFACE}} repeat {{COUNT}}

1 step · 3 inputs

Send

ping {{HOST}} source {{IFACE}} repeat {{COUNT}}

Sends Enter afterwards.

Traceroute

Run: traceroute {{HOST}}

1 step · 1 input

Send
```
traceroute {{HOST}}
```
Sends Enter afterwards.

Traceroute in VRF

Run: traceroute vrf {{VRF}} {{HOST}}

1 step · 2 inputs

Send
```
traceroute vrf {{VRF}} {{HOST}}
```
Sends Enter afterwards.

Add Static Route

Run: configure ; ip route {{PREFIX}} {{NEXT_HOP}} ; end

3 steps · asks for confirmation before it runs · 2 inputs

Send
```
configure
```
Sends Enter afterwards.
Send
```
ip route {{PREFIX}} {{NEXT_HOP}}
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Add SVI

Run: configure ; interface Vlan{{VLAN}} ; ip address {{IP}}/{{PREFIX_LEN}} ; no shutdown ; end

5 steps · asks for confirmation before it runs · 3 inputs

Send
```
configure
```
Sends Enter afterwards.
Send
```
interface Vlan{{VLAN}}
```
Sends Enter afterwards.
Send
```
ip address {{IP}}/{{PREFIX_LEN}}
```
Sends Enter afterwards.
Send
```
no shutdown
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Add BGP Neighbour

Run: configure ; router bgp {{ASN}} ; neighbor {{PEER}} remote-as {{PEER_AS}} ; neighbor {{PEER}} description {{DESCRIPTION}} ; end

5 steps · asks for confirmation before it runs · 4 inputs

Send
```
configure
```
Sends Enter afterwards.
Send
```
router bgp {{ASN}}
```
Sends Enter afterwards.
Send
```
neighbor {{PEER}} remote-as {{PEER_AS}}
```
Sends Enter afterwards.

Send

neighbor {{PEER}} description {{DESCRIPTION}}

Sends Enter afterwards.

Send
```
end
```
Sends Enter afterwards.

Remove Static Route

Run: configure ; no ip route {{PREFIX}} {{NEXT_HOP}} ; end

4 steps · asks for confirmation before it runs · 2 inputs

Confirm

Asks yes or no: “Remove the route to {{PREFIX}}. Traffic for it follows whatever is left in the table, or nothing at all. Continue?”

Answering no stops the script here.
Send
```
configure
```
Sends Enter afterwards.
Send
```
no ip route {{PREFIX}} {{NEXT_HOP}}
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Clear BGP Neighbour

Run: clear ip bgp {{PEER}}

2 steps · asks for confirmation before it runs · 1 input

Confirm

Asks yes or no: “Reset the BGP session with {{PEER}}. Every prefix learned from it is withdrawn until the session rebuilds — on a spine peer this reconverges the fabric. Continue?”

Answering no stops the script here.
Send
```
clear ip bgp {{PEER}}
```
Sends Enter afterwards.

Soft-Clear BGP Neighbour

Run: clear ip bgp {{PEER}} soft in

2 steps · asks for confirmation before it runs · 1 input

Confirm

Asks yes or no: “Re-request routes from {{PEER}} without dropping the session. Prefixes may churn while it settles. Continue?”

Answering no stops the script here.
Send
```
clear ip bgp {{PEER}} soft in
```
Sends Enter afterwards.

Clear ARP Cache

Run: clear ip arp

2 steps · asks for confirmation before it runs

Confirm

Asks yes or no: “Flush the ARP cache. Expect a burst of re-resolution and a brief pause on active flows. Continue?”

Answering no stops the script here.
Send
```
clear ip arp
```
Sends Enter afterwards.

Arista EOS - System & Config Sessions

47 buttons

Config sessions, diffs, rollback, logs and hardware health.

Version & Uptime

Run: show version

1 step

Send
```
show version
```
Sends Enter afterwards.

Running Config

Run: show running-config

1 step

Send
```
show running-config
```
Sends Enter afterwards.

Running Config Section

Run: show running-config section {{PATTERN}}

1 step · 1 input

Send
```
show running-config section {{PATTERN}}
```
Sends Enter afterwards.

Startup Config

Run: show startup-config

1 step

Send
```
show startup-config
```
Sends Enter afterwards.

Config Diff vs Startup

Run: show running-config diffs

1 step

Send
```
show running-config diffs
```
Sends Enter afterwards.

Config Sessions

Run: show configuration sessions

1 step

Send
```
show configuration sessions
```
Sends Enter afterwards.

Session Detail

Run: show configuration sessions detail

1 step

Send
```
show configuration sessions detail
```
Sends Enter afterwards.

Checkpoint List

Run: show checkpoints

1 step

Send
```
show checkpoints
```
Sends Enter afterwards.

Environment

Run: show environment all

1 step

Send
```
show environment all
```
Sends Enter afterwards.

Temperature

Run: show environment temperature

1 step

Send
```
show environment temperature
```
Sends Enter afterwards.

Power Supplies

Run: show environment power

1 step

Send
```
show environment power
```
Sends Enter afterwards.

Cooling

Run: show environment cooling

1 step

Send
```
show environment cooling
```
Sends Enter afterwards.

Hardware Inventory

Run: show inventory

1 step

Send
```
show inventory
```
Sends Enter afterwards.

CPU Usage

Run: show processes top once

1 step

Send
```
show processes top once
```
Sends Enter afterwards.

Memory Usage

Run: show version detail | grep -i memory

1 step

Send
```
show version detail | grep -i memory
```
Sends Enter afterwards.

Filesystem Usage

Run: dir flash:

1 step

Send
```
dir flash:
```
Sends Enter afterwards.

Agent Status

Run: show agent logs crash

1 step

Send
```
show agent logs crash
```
Sends Enter afterwards.

Recent Log

Run: show logging last {{LINES}}

1 step · 1 input

Send
```
show logging last {{LINES}}
```
Sends Enter afterwards.

Search Log

Run: show logging | include {{PATTERN}}

1 step · 1 input

Send
```
show logging | include {{PATTERN}}
```
Sends Enter afterwards.

Log Since Boot

Run: show logging system

1 step

Send
```
show logging system
```
Sends Enter afterwards.

NTP Status

Run: show ntp status

1 step

Send
```
show ntp status
```
Sends Enter afterwards.

NTP Associations

Run: show ntp associations

1 step

Send
```
show ntp associations
```
Sends Enter afterwards.

Clock

Run: show clock

1 step

Send
```
show clock
```
Sends Enter afterwards.

Users Logged In

Run: show users detail

1 step

Send
```
show users detail
```
Sends Enter afterwards.

AAA Config

Run: show running-config section aaa

1 step

Send
```
show running-config section aaa
```
Sends Enter afterwards.

Management Interfaces

Run: show ip interface brief | include Management

1 step

Send

show ip interface brief | include Management

Sends Enter afterwards.

SNMP Config

Run: show running-config section snmp

1 step

Send
```
show running-config section snmp
```
Sends Enter afterwards.

eAPI Status

Run: show management api http-commands

1 step

Send
```
show management api http-commands
```
Sends Enter afterwards.

Scheduled Jobs

Run: show schedule summary

1 step

Send
```
show schedule summary
```
Sends Enter afterwards.

Boot Config

Run: show boot-config

1 step

Send
```
show boot-config
```
Sends Enter afterwards.

Save Running Config

Run: write memory

1 step · asks for confirmation before it runs

Writes configuration to persistent storage

Send
```
write memory
```
Sends Enter afterwards.

Set Hostname

Run: configure ; hostname {{HOSTNAME}} ; end

3 steps · asks for confirmation before it runs · 1 input

Send
```
configure
```
Sends Enter afterwards.
Send
```
hostname {{HOSTNAME}}
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Add NTP Server

Run: configure ; ntp server {{NTP}} ; end

3 steps · asks for confirmation before it runs · 1 input

Send
```
configure
```
Sends Enter afterwards.
Send
```
ntp server {{NTP}}
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Set Logging Host

Run: configure ; logging host {{SERVER}} ; end

3 steps · asks for confirmation before it runs · 1 input

Send
```
configure
```
Sends Enter afterwards.
Send
```
logging host {{SERVER}}
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Create Checkpoint

A named snapshot of the running config. Take one before any risky change.

1 step · asks for confirmation before it runs · 1 input

Send
```
copy running-config checkpoint:{{NAME}}
```
Sends Enter afterwards.

Start Config Session

Stages changes without applying them. Nothing takes effect until you commit.

2 steps · asks for confirmation before it runs · 1 input

Send
```
configure session {{NAME}}
```
Sends Enter afterwards.
Send
```
show session-config diffs
```
Sends Enter afterwards.

Show Session Diff

Run: configure session {{NAME}} ; show session-config diffs ; end

3 steps · asks for confirmation before it runs · 1 input

Send
```
configure session {{NAME}}
```
Sends Enter afterwards.
Send
```
show session-config diffs
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Commit Config Session

Run: configure session {{NAME}} ; commit ; end

3 steps · asks for confirmation before it runs · 1 input

Send
```
configure session {{NAME}}
```
Sends Enter afterwards.
Send
```
commit
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Commit with Timer

Commits with an automatic rollback unless confirmed in time — the safe way to change something you are connected through.

3 steps · asks for confirmation before it runs · 2 inputs

Send
```
configure session {{NAME}}
```
Sends Enter afterwards.
Send
```
commit timer {{TIME}}
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Confirm Pending Commit

Run: configure ; no commit timer ; end

3 steps · asks for confirmation before it runs

Send
```
configure
```
Sends Enter afterwards.
Send
```
no commit timer
```
Sends Enter afterwards.
Send
```
end
```
Sends Enter afterwards.

Abort Config Session

Run: configure session {{NAME}} ; abort

3 steps · asks for confirmation before it runs · 1 input

Confirm

Asks yes or no: “Discard everything staged in session {{NAME}}, including work a colleague may have staged there. Continue?”

Answering no stops the script here.
Send
```
configure session {{NAME}}
```
Sends Enter afterwards.
Send
```
abort
```
Sends Enter afterwards.

Roll Back to Checkpoint

Run: configure replace checkpoint:{{NAME}}

2 steps · asks for confirmation before it runs · 1 input

Confirm

Asks yes or no: “Replace the running config with checkpoint {{NAME}}. Anything configured since that checkpoint is removed, including the management access you are using. Continue?”

Answering no stops the script here.
Send
```
configure replace checkpoint:{{NAME}}
```
Sends Enter afterwards.

Roll Back to Startup Config

Run: configure replace startup-config

2 steps · asks for confirmation before it runs

Confirm

Asks yes or no: “Replace the running config with the startup config. Every unsaved change is undone at once. Continue?”

Answering no stops the script here.
Send
```
configure replace startup-config
```
Sends Enter afterwards.

Reload Device

Run: reload now

2 steps · asks for confirmation before it runs

Reboots or reloads the device

Confirm

Asks yes or no: “Reload this switch immediately. Everything through it stops for the length of the boot, and unsaved config is lost. Continue?”

Answering no stops the script here.
Send
```
reload now
```
Sends Enter afterwards.

Reload in Minutes

Run: reload in {{MINUTES}}

2 steps · asks for confirmation before it runs · 1 input

Reboots or reloads the device

Confirm

Asks yes or no: “Schedule a reload in {{MINUTES}} minutes. Useful as a safety net for a risky change — but it will drop everything through this switch when it fires. Continue?”

Answering no stops the script here.
Send
```
reload in {{MINUTES}}
```
Sends Enter afterwards.

Cancel Scheduled Reload

Run: reload cancel

1 step · asks for confirmation before it runs

Reboots or reloads the device

Send
```
reload cancel
```
Sends Enter afterwards.

Clear Log Buffer

Run: clear logging

2 steps · asks for confirmation before it runs

Confirm

Asks yes or no: “Discard the buffered log. Whatever explains the current problem goes with it. Continue?”

Answering no stops the script here.
Send
```
clear logging
```
Sends Enter afterwards.

Version history

Revision 1 current

First published version.

14 Aug 2026 · 137.2 KB · needs 1.0.0+ · 19573f13902d1510…

View Download