Aruba AOS-CX

AOS-CX switches: ports, VLANs, LAGs, VSX and checkpoint rollback.

HPE / Aruba Requires SmartCom Revisited 1.0.0 or newer

by Nathan Kirk · 69 downloads · MIT licence · revision 1 · published 14 Aug 2026

This bundle can change or destroy device state

Shuts down an interface (2 steps) — Administratively disables an interface. If it is the interface you are connected over, you lose the session.
Erases configuration or storage (1 step) — Wipes stored configuration or a filesystem on the device. Usually not recoverable without a backup.
Writes configuration to persistent storage (1 step) — Makes the current configuration survive a reboot. Intended, usually — but it is not a read-only button.

Show exactly which steps matched

Shut Down Interface — Shuts down an interface (steps[3], sent text)
```
shutdown
```
Bounce Interface — Shuts down an interface (steps[3], sent text)
```
shutdown
```
Save Running Config — Writes configuration to persistent storage (steps[0], sent text)
```
copy running-config startup-config
```
Erase Startup Config — Erases configuration or storage (steps[1], sent text)
```
erase startup-config
```

Flagged automatically by matching command text. It is a prompt to read the script, not a verdict — plenty of legitimate buttons reboot things on purpose.

3 sets, 117 buttons, 198 steps · 141.6 KB

File format version 1 · exported by Smartcom Revisited

Download .buttons.json

SHA-256 ee4d9edf0c1abb535e9e55560039c709fe6e561f46168633df48236fd3ca7b15

You get the exact file the uploader submitted, byte for byte — that checksum is what sha256sum will print. Import it from the button panel in SmartCom Revisited.

About this set

Aruba AOS-CX day-to-day: port and PoE state, VLAN and LAG configuration, VSX pair health, routing and access control, with checkpoints and rollback as the safety net for config changes.

Every button, in full

Exactly what gets sent

This is the complete script of the file below — nothing is summarised or hidden. Read it before you download it, the same way you would read a script someone emailed you.

AOS-CX - Ports, VLANs & PoE

36 buttons

Interface state, VLANs, LAGs, PoE budget and MAC learning.

Interface Brief

Run: show interface brief

1 step

Send
```
show interface brief
```
Sends Enter afterwards.

Interface Detail

Run: show interface {{IFACE}}

1 step · 1 input

Send
```
show interface {{IFACE}}
```
Sends Enter afterwards.

Interface Statistics

Run: show interface {{IFACE}} statistics

1 step · 1 input

Send
```
show interface {{IFACE}} statistics
```
Sends Enter afterwards.

Interface Errors

Run: show interface {{IFACE}} extended

1 step · 1 input

Send
```
show interface {{IFACE}} extended
```
Sends Enter afterwards.

Transceiver Detail

Run: show interface {{IFACE}} transceiver detail

1 step · 1 input

Send

show interface {{IFACE}} transceiver detail

Sends Enter afterwards.

All Transceivers

Run: show interface transceiver

1 step

Send
```
show interface transceiver
```
Sends Enter afterwards.

VLAN Summary

Run: show vlan

1 step

Send
```
show vlan
```
Sends Enter afterwards.

VLAN Detail

Run: show vlan {{VLAN}}

1 step · 1 input

Send
```
show vlan {{VLAN}}
```
Sends Enter afterwards.

VLAN Ports

Run: show vlan port {{IFACE}}

1 step · 1 input

Send
```
show vlan port {{IFACE}}
```
Sends Enter afterwards.

LAG Summary

Run: show lacp interfaces

1 step

Send
```
show lacp interfaces
```
Sends Enter afterwards.

LAG Detail

Run: show interface lag {{LAG}}

1 step · 1 input

Send
```
show interface lag {{LAG}}
```
Sends Enter afterwards.

LACP Aggregates

Run: show lacp aggregates

1 step

Send
```
show lacp aggregates
```
Sends Enter afterwards.

MAC Address Table

Run: show mac-address-table

1 step

Send
```
show mac-address-table
```
Sends Enter afterwards.

Find MAC Address

Run: show mac-address-table address {{MAC}}

1 step · 1 input

Send
```
show mac-address-table address {{MAC}}
```
Sends Enter afterwards.

MAC Table by Port

Run: show mac-address-table port {{IFACE}}

1 step · 1 input

Send
```
show mac-address-table port {{IFACE}}
```
Sends Enter afterwards.

MAC Table Count

Run: show mac-address-table count

1 step

Send
```
show mac-address-table count
```
Sends Enter afterwards.

Spanning-Tree Summary

Run: show spanning-tree summary

1 step

Send
```
show spanning-tree summary
```
Sends Enter afterwards.

Spanning-Tree Detail

Run: show spanning-tree detail

1 step

Send
```
show spanning-tree detail
```
Sends Enter afterwards.

Spanning-Tree Inconsistent Ports

Run: show spanning-tree inconsistent-ports

1 step

Send
```
show spanning-tree inconsistent-ports
```
Sends Enter afterwards.

PoE Overview

Run: show power-over-ethernet brief

1 step

Send
```
show power-over-ethernet brief
```
Sends Enter afterwards.

PoE Port Detail

Run: show power-over-ethernet interface {{IFACE}}

1 step · 1 input

Send

show power-over-ethernet interface {{IFACE}}

Sends Enter afterwards.

LLDP Neighbours

Run: show lldp neighbor-info

1 step

Send
```
show lldp neighbor-info
```
Sends Enter afterwards.

LLDP Neighbour Detail

Run: show lldp neighbor-info interface {{IFACE}} detail

1 step · 1 input

Send

show lldp neighbor-info interface {{IFACE}} detail

Sends Enter afterwards.

Loop Protect Status

Run: show loop-protect

1 step

Send
```
show loop-protect
```
Sends Enter afterwards.

Set Interface Description

Run: configure terminal ; interface {{IFACE}} ; description {{DESCRIPTION}} ; exit ; exit

5 steps · asks for confirmation before it runs · 2 inputs

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
description {{DESCRIPTION}}
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Set Access VLAN

Run: configure terminal ; interface {{IFACE}} ; no routing ; vlan access {{VLAN}} ; exit ; exit

6 steps · asks for confirmation before it runs · 2 inputs

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
no routing
```
Sends Enter afterwards.
Send
```
vlan access {{VLAN}}
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Configure Trunk Port

Run: configure terminal ; interface {{IFACE}} ; no routing ; vlan trunk native {{NATIVE_VLAN}} ; vlan trunk allowed {{VLAN_LIST}} ; exit ; exit

7 steps · asks for confirmation before it runs · 3 inputs

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
no routing
```
Sends Enter afterwards.
Send
```
vlan trunk native {{NATIVE_VLAN}}
```
Sends Enter afterwards.
Send
```
vlan trunk allowed {{VLAN_LIST}}
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Create VLAN

Run: configure terminal ; vlan {{VLAN}} ; name {{VLAN_NAME}} ; exit ; exit

5 steps · asks for confirmation before it runs · 2 inputs

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
vlan {{VLAN}}
```
Sends Enter afterwards.
Send
```
name {{VLAN_NAME}}
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Enable Interface

Run: configure terminal ; interface {{IFACE}} ; no shutdown ; exit ; exit

5 steps · asks for confirmation before it runs · 1 input

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
no shutdown
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Enable PoE on Port

Run: configure terminal ; interface {{IFACE}} ; power-over-ethernet ; exit ; exit

5 steps · asks for confirmation before it runs · 1 input

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
power-over-ethernet
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Add Port to LAG

Run: configure terminal ; interface {{IFACE}} ; lag {{LAG}} ; exit ; exit

5 steps · asks for confirmation before it runs · 2 inputs

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
lag {{LAG}}
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Shut Down Interface

Run: configure terminal ; interface {{IFACE}} ; shutdown ; exit ; exit

6 steps · asks for confirmation before it runs · 1 input

Shuts down an interface

Confirm

Asks yes or no: “Shut down {{IFACE}}. Anything behind it loses its link immediately. Continue?”

Answering no stops the script here.
Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
shutdown
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Disable PoE on Port

Run: configure terminal ; interface {{IFACE}} ; no power-over-ethernet ; exit ; exit

6 steps · asks for confirmation before it runs · 1 input

Confirm

Asks yes or no: “Cut power to {{IFACE}}. Whatever it powers — phone, camera, AP — turns off at once. Continue?”

Answering no stops the script here.
Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
no power-over-ethernet
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Bounce Interface

Run: configure terminal ; interface {{IFACE}} ; shutdown ; no shutdown ; exit ; exit

7 steps · asks for confirmation before it runs · 1 input

Shuts down an interface

Confirm

Asks yes or no: “Bounce {{IFACE}}. The link drops and comes back, and devices behind it reconnect. Continue?”

Answering no stops the script here.
Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
interface {{IFACE}}
```
Sends Enter afterwards.
Send
```
shutdown
```
Sends Enter afterwards.
Send
```
no shutdown
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Clear Interface Statistics

Run: clear interface {{IFACE}} statistics

2 steps · asks for confirmation before it runs · 1 input

Confirm

Asks yes or no: “Reset the counters on {{IFACE}}. The error history you are looking at is lost. Continue?”

Answering no stops the script here.
Send
```
clear interface {{IFACE}} statistics
```
Sends Enter afterwards.

Delete VLAN

Run: configure terminal ; no vlan {{VLAN}} ; exit

4 steps · asks for confirmation before it runs · 1 input

Confirm

Asks yes or no: “Delete VLAN {{VLAN}}. Ports left in it lose their network. Continue?”

Answering no stops the script here.
Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
no vlan {{VLAN}}
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

AOS-CX - Routing & VSX

36 buttons

Routes, OSPF, BGP, VRRP, VSX pair health and reachability.

Routing Table

Run: show ip route

1 step

Send
```
show ip route
```
Sends Enter afterwards.

Route for Prefix

Run: show ip route {{PREFIX}}

1 step · 1 input

Send
```
show ip route {{PREFIX}}
```
Sends Enter afterwards.

Route Summary

Run: show ip route summary

1 step

Send
```
show ip route summary
```
Sends Enter afterwards.

Connected Routes

Run: show ip route connected

1 step

Send
```
show ip route connected
```
Sends Enter afterwards.

Static Routes

Run: show ip route static

1 step

Send
```
show ip route static
```
Sends Enter afterwards.

Routes in VRF

Run: show ip route vrf {{VRF}}

1 step · 1 input

Send
```
show ip route vrf {{VRF}}
```
Sends Enter afterwards.

ARP Table

Run: show arp

1 step

Send
```
show arp
```
Sends Enter afterwards.

ARP for Host

Run: show arp | include {{IP}}

1 step · 1 input

Send
```
show arp | include {{IP}}
```
Sends Enter afterwards.

IP Interfaces

Run: show ip interface brief

1 step

Send
```
show ip interface brief
```
Sends Enter afterwards.

SVI Detail

Run: show interface vlan{{VLAN}}

1 step · 1 input

Send
```
show interface vlan{{VLAN}}
```
Sends Enter afterwards.

OSPF Neighbours

Run: show ip ospf neighbors

1 step

Send
```
show ip ospf neighbors
```
Sends Enter afterwards.

OSPF Interfaces

Run: show ip ospf interface

1 step

Send
```
show ip ospf interface
```
Sends Enter afterwards.

OSPF Routes

Run: show ip ospf routes

1 step

Send
```
show ip ospf routes
```
Sends Enter afterwards.

BGP Summary

Run: show bgp ipv4 unicast summary

1 step

Send
```
show bgp ipv4 unicast summary
```
Sends Enter afterwards.

BGP Neighbours

Run: show bgp ipv4 unicast neighbors

1 step

Send
```
show bgp ipv4 unicast neighbors
```
Sends Enter afterwards.

BGP Routes

Run: show bgp ipv4 unicast

1 step

Send
```
show bgp ipv4 unicast
```
Sends Enter afterwards.

VRRP Status

Run: show vrrp

1 step

Send
```
show vrrp
```
Sends Enter afterwards.

VRRP Detail

Run: show vrrp all detail

1 step

Send
```
show vrrp all detail
```
Sends Enter afterwards.

Active Gateway

Run: show active-gateway

1 step

Send
```
show active-gateway
```
Sends Enter afterwards.

VSX Status

Run: show vsx status

1 step

Send
```
show vsx status
```
Sends Enter afterwards.

VSX Brief

Run: show vsx brief

1 step

Send
```
show vsx brief
```
Sends Enter afterwards.

VSX ISL Status

Run: show vsx status linkup-delay

1 step

Send
```
show vsx status linkup-delay
```
Sends Enter afterwards.

VSX Configuration Consistency

Run: show vsx configuration-consistency

1 step

Send
```
show vsx configuration-consistency
```
Sends Enter afterwards.

MCLAG Interfaces

Run: show lacp interfaces multi-chassis

1 step

Send
```
show lacp interfaces multi-chassis
```
Sends Enter afterwards.

DHCP Relay Status

Run: show dhcp-relay

1 step

Send
```
show dhcp-relay
```
Sends Enter afterwards.

DHCP Snooping Bindings

Run: show dhcp-snooping binding

1 step

Send
```
show dhcp-snooping binding
```
Sends Enter afterwards.

Ping Host

Run: ping {{HOST}} repetitions {{COUNT}}

1 step · 2 inputs

Send
```
ping {{HOST}} repetitions {{COUNT}}
```
Sends Enter afterwards.

Ping in VRF

Run: ping {{HOST}} vrf {{VRF}} repetitions {{COUNT}}

1 step · 3 inputs

Send

ping {{HOST}} vrf {{VRF}} repetitions {{COUNT}}

Sends Enter afterwards.

Traceroute

Run: traceroute {{HOST}}

1 step · 1 input

Send
```
traceroute {{HOST}}
```
Sends Enter afterwards.

Traceroute in VRF

Run: traceroute {{HOST}} vrf {{VRF}}

1 step · 2 inputs

Send
```
traceroute {{HOST}} vrf {{VRF}}
```
Sends Enter afterwards.

Add Static Route

Run: configure terminal ; ip route {{PREFIX}} {{NEXT_HOP}} ; exit

3 steps · asks for confirmation before it runs · 2 inputs

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
ip route {{PREFIX}} {{NEXT_HOP}}
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Create SVI

Run: configure terminal ; interface vlan{{VLAN}} ; ip address {{IP}}/{{PREFIX_LEN}} ; no shutdown ; exit ; exit

6 steps · asks for confirmation before it runs · 3 inputs

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
interface vlan{{VLAN}}
```
Sends Enter afterwards.
Send
```
ip address {{IP}}/{{PREFIX_LEN}}
```
Sends Enter afterwards.
Send
```
no shutdown
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Add BGP Neighbour

Run: configure terminal ; router bgp {{ASN}} ; neighbor {{PEER}} remote-as {{PEER_AS}} ; exit ; exit

5 steps · asks for confirmation before it runs · 3 inputs

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
router bgp {{ASN}}
```
Sends Enter afterwards.
Send
```
neighbor {{PEER}} remote-as {{PEER_AS}}
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Remove Static Route

Run: configure terminal ; no ip route {{PREFIX}} {{NEXT_HOP}} ; exit

4 steps · asks for confirmation before it runs · 2 inputs

Confirm

Asks yes or no: “Remove the route to {{PREFIX}}. Traffic for it follows whatever is left, or nothing. Continue?”

Answering no stops the script here.
Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
no ip route {{PREFIX}} {{NEXT_HOP}}
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Clear ARP Cache

Run: clear arp

2 steps · asks for confirmation before it runs

Confirm

Asks yes or no: “Flush the ARP cache. Expect a brief pause on active flows while it repopulates. Continue?”

Answering no stops the script here.
Send
```
clear arp
```
Sends Enter afterwards.

Clear BGP Neighbour

Run: clear bgp {{PEER}}

2 steps · asks for confirmation before it runs · 1 input

Confirm

Asks yes or no: “Reset the BGP session with {{PEER}}. Prefixes from that peer are withdrawn until it rebuilds. Continue?”

Answering no stops the script here.
Send
```
clear bgp {{PEER}}
```
Sends Enter afterwards.

AOS-CX - System, Checkpoints & Rescue

45 buttons

Health, logs, users, checkpoints, rollback and reboot.

Version

Run: show version

1 step

Send
```
show version
```
Sends Enter afterwards.

System Summary

Run: show system

1 step

Send
```
show system
```
Sends Enter afterwards.

Uptime & Resources

Run: show system resource-utilization

1 step

Send
```
show system resource-utilization
```
Sends Enter afterwards.

CPU Usage

Run: show system resource-utilization | include CPU

1 step

Send

show system resource-utilization | include CPU

Sends Enter afterwards.

Memory Usage

Run: show system resource-utilization | include Memory

1 step

Send

show system resource-utilization | include Memory

Sends Enter afterwards.

Environment

Run: show environment temperature

1 step

Send
```
show environment temperature
```
Sends Enter afterwards.

Power Supplies

Run: show environment power-supply

1 step

Send
```
show environment power-supply
```
Sends Enter afterwards.

Fan Status

Run: show environment fan

1 step

Send
```
show environment fan
```
Sends Enter afterwards.

LED Status

Run: show environment led

1 step

Send
```
show environment led
```
Sends Enter afterwards.

Module Inventory

Run: show module

1 step

Send
```
show module
```
Sends Enter afterwards.

Stack Status

Run: show vsf

1 step

Send
```
show vsf
```
Sends Enter afterwards.

Filesystem Usage

Run: show core-dump

1 step

Send
```
show core-dump
```
Sends Enter afterwards.

Running Config

Run: show running-config

1 step

Send
```
show running-config
```
Sends Enter afterwards.

Running Config Section

Run: show running-config interface {{IFACE}}

1 step · 1 input

Send
```
show running-config interface {{IFACE}}
```
Sends Enter afterwards.

Startup Config

Run: show startup-config

1 step

Send
```
show startup-config
```
Sends Enter afterwards.

Config Differences

Run: checkpoint diff startup-config running-config

1 step

Send

checkpoint diff startup-config running-config

Sends Enter afterwards.

Checkpoint List

Run: show checkpoint

1 step

Send
```
show checkpoint
```
Sends Enter afterwards.

Checkpoint Detail

Run: show checkpoint {{NAME}}

1 step · 1 input

Send
```
show checkpoint {{NAME}}
```
Sends Enter afterwards.

Event Log

Run: show events -n {{LINES}}

1 step · 1 input

Send
```
show events -n {{LINES}}
```
Sends Enter afterwards.

Search Event Log

Run: show events | include {{PATTERN}}

1 step · 1 input

Send
```
show events | include {{PATTERN}}
```
Sends Enter afterwards.

Error Events

Run: show events -s emer,alert,crit,err -n {{LINES}}

1 step · 1 input

Send

show events -s emer,alert,crit,err -n {{LINES}}

Sends Enter afterwards.

Logging Config

Run: show running-config | include logging

1 step

Send
```
show running-config | include logging
```
Sends Enter afterwards.

Users

Run: show user-list

1 step

Send
```
show user-list
```
Sends Enter afterwards.

AAA Config

Run: show aaa authentication

1 step

Send
```
show aaa authentication
```
Sends Enter afterwards.

Active Sessions

Run: show session

1 step

Send
```
show session
```
Sends Enter afterwards.

SSH Server Config

Run: show ssh server

1 step

Send
```
show ssh server
```
Sends Enter afterwards.

Management Interface

Run: show interface mgmt

1 step

Send
```
show interface mgmt
```
Sends Enter afterwards.

NTP Status

Run: show ntp status

1 step

Send
```
show ntp status
```
Sends Enter afterwards.

NTP Associations

Run: show ntp associations

1 step

Send
```
show ntp associations
```
Sends Enter afterwards.

Clock

Run: show clock

1 step

Send
```
show clock
```
Sends Enter afterwards.

SNMP Config

Run: show snmp-server

1 step

Send
```
show snmp-server
```
Sends Enter afterwards.

Copp Policy

Run: show copp-policy statistics

1 step

Send
```
show copp-policy statistics
```
Sends Enter afterwards.

Save Running Config

Run: copy running-config startup-config

1 step · asks for confirmation before it runs

Writes configuration to persistent storage

Send
```
copy running-config startup-config
```
Sends Enter afterwards.

Set Hostname

Run: configure terminal ; hostname {{HOSTNAME}} ; exit

3 steps · asks for confirmation before it runs · 1 input

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
hostname {{HOSTNAME}}
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Add NTP Server

Run: configure terminal ; ntp server {{NTP}} ; exit

3 steps · asks for confirmation before it runs · 1 input

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
ntp server {{NTP}}
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Set Logging Host

Run: configure terminal ; logging {{SERVER}} ; exit

3 steps · asks for confirmation before it runs · 1 input

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
logging {{SERVER}}
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Create Checkpoint

Named snapshot of the running config. Take one before any change you might need to undo.

1 step · asks for confirmation before it runs · 1 input

Send
```
copy running-config checkpoint {{NAME}}
```
Sends Enter afterwards.

Back Up Config to TFTP

Run: copy running-config tftp://{{SERVER}}/{{FILE}}

1 step · asks for confirmation before it runs · 2 inputs

Send

copy running-config tftp://{{SERVER}}/{{FILE}}

Sends Enter afterwards.

Enable Auto-Checkpoint

Automatically checkpoints the config every 5 minutes after a change.

3 steps · asks for confirmation before it runs

Send
```
configure terminal
```
Sends Enter afterwards.
Send
```
checkpoint auto 5
```
Sends Enter afterwards.
Send
```
exit
```
Sends Enter afterwards.

Roll Back to Checkpoint

Run: copy checkpoint {{NAME}} running-config

2 steps · asks for confirmation before it runs · 1 input

Confirm

Asks yes or no: “Replace the running config with checkpoint {{NAME}}. Everything configured since is undone, which may include the access you are using now. Continue?”

Answering no stops the script here.
Send
```
copy checkpoint {{NAME}} running-config
```
Sends Enter afterwards.

Roll Back to Startup Config

Run: copy startup-config running-config

2 steps · asks for confirmation before it runs

Confirm

Asks yes or no: “Replace the running config with the startup config. Every unsaved change is undone at once. Continue?”

Answering no stops the script here.
Send
```
copy startup-config running-config
```
Sends Enter afterwards.

Restore Config from TFTP

Run: copy tftp://{{SERVER}}/{{FILE}} running-config

2 steps · asks for confirmation before it runs · 2 inputs

Confirm

Asks yes or no: “Replace the running config with {{FILE}}. Anything not in that file is removed, including management access. Continue?”

Answering no stops the script here.

Send

copy tftp://{{SERVER}}/{{FILE}} running-config

Sends Enter afterwards.

Reboot Switch

Run: boot system

2 steps · asks for confirmation before it runs

Confirm

Asks yes or no: “Reboot this switch. Everything through it stops for the length of the boot, and unsaved config is lost. Continue?”

Answering no stops the script here.
Send
```
boot system
```
Sends Enter afterwards.

Erase Startup Config

Run: erase startup-config

2 steps · asks for confirmation before it runs

Erases configuration or storage

Confirm

Asks yes or no: “Erase the startup config. On the next reboot this switch comes up unconfigured with no management access. Continue?”

Answering no stops the script here.
Send
```
erase startup-config
```
Sends Enter afterwards.

Factory Reset

Run: erase all zeroize

2 steps · asks for confirmation before it runs

Confirm

Asks yes or no: “Wipe the switch completely, including config, logs and keys, and reboot to factory state. Recovery needs console access. Continue?”

Answering no stops the script here.
Send
```
erase all zeroize
```
Sends Enter afterwards.

Version history

Revision 1 current

First published version.

14 Aug 2026 · 141.6 KB · needs 1.0.0+ · ee4d9edf0c1abb53…

View Download