MikroTik Router & Network Commands

MikroTik Requires SmartCom Revisited 1.0.0 or newer

by Nathan Kirk · 81 downloads · MIT licence · revision 1 · published 13 Aug 2026

This bundle can change or destroy device state

Reboots or reloads the device (1 step) — Restarts the device. Any session on it drops, and anything not saved is lost.
Shuts down an interface (1 step) — Administratively disables an interface. If it is the interface you are connected over, you lose the session.
Factory resets the device (1 step) — Returns the device to factory settings, including management addressing. Expect to need console access afterwards.

Show exactly which steps matched

Reboot Router — Reboots or reloads the device (steps[0], sent text)
```
/system reboot
```
Shut Down Router — Shuts down an interface (steps[0], sent text)
```
/system shutdown
```

Reset Configuration — Factory resets the device (steps[0], sent text)

/system reset-configuration no-defaults={{NO_DEFAULTS}} skip-backup={{SKIP_BACKUP}}

Flagged automatically by matching command text. It is a prompt to read the script, not a verdict — plenty of legitimate buttons reboot things on purpose.

6 sets, 135 buttons, 135 steps · 143.9 KB

File format version 1 · exported by Smartcom Revisited

Download .buttons.json

SHA-256 89a37bcb97eaf9b9b49a572b2a75f2d1f271e45c7fb5c400291f8bc2d91f39f8

You get the exact file the uploader submitted, byte for byte — that checksum is what sha256sum will print. Import it from the button panel in SmartCom Revisited.

About this set

RouterOS commands for configuring interfaces, bridges, VLANs, IP addresses, routing, BGP, OSPF, firewall rules, NAT, DHCP, DNS, ARP, and network services.

Every button, in full

Exactly what gets sent

This is the complete script of the file below — nothing is summarised or hidden. Read it before you download it, the same way you would read a script someone emailed you.

MikroTik - System & Identity

17 buttons

Show RouterOS Resources

Run: /system resource print

1 step

Send
```
/system resource print
```
Sends Enter afterwards.

Show RouterBOARD Information

Run: /system routerboard print

1 step

Send
```
/system routerboard print
```
Sends Enter afterwards.

Show RouterOS Packages

Run: /system package print

1 step

Send
```
/system package print
```
Sends Enter afterwards.

Show License

Run: /system license print

1 step

Send
```
/system license print
```
Sends Enter afterwards.

Show Clock

Run: /system clock print

1 step

Send
```
/system clock print
```
Sends Enter afterwards.

Set Router Identity

Run: /system identity set name="{{IDENTITY}}"

1 step · 1 input

Send

/system identity set name="{{IDENTITY}}"

Sends Enter afterwards.

Set Time Zone

Run: /system clock set time-zone-name="{{TIME_ZONE}}"

1 step · 1 input

Send

/system clock set time-zone-name="{{TIME_ZONE}}"

Sends Enter afterwards.

Show NTP Client

Run: /system ntp client print

1 step

Send
```
/system ntp client print
```
Sends Enter afterwards.

Enable NTP Client

Run: /system ntp client set enabled=yes servers="{{NTP_SERVERS}}"

1 step · 1 input

Send

/system ntp client set enabled=yes servers="{{NTP_SERVERS}}"

Sends Enter afterwards.

Disable NTP Client

Run: /system ntp client set enabled=no

1 step

Send
```
/system ntp client set enabled=no
```
Sends Enter afterwards.

Show System Note

Run: /system note print

1 step

Send
```
/system note print
```
Sends Enter afterwards.

Set System Note

Run: /system note set note="{{NOTE}}" show-at-login=yes

1 step · 1 input

Send

/system note set note="{{NOTE}}" show-at-login=yes

Sends Enter afterwards.

Show Environment Health

Run: /system health print

1 step

Send
```
/system health print
```
Sends Enter afterwards.

Show Reboot History

Run: /system history print

1 step

Send
```
/system history print
```
Sends Enter afterwards.

Reboot Router

Run: /system reboot

1 step · asks for confirmation before it runs

Reboots or reloads the device

Send
```
/system reboot
```
Sends Enter afterwards.

Shut Down Router

Run: /system shutdown

1 step · asks for confirmation before it runs

Shuts down an interface

Send
```
/system shutdown
```
Sends Enter afterwards.

Reset Configuration

Run: /system reset-configuration no-defaults={{NO_DEFAULTS}} skip-backup={{SKIP_BACKUP}}

1 step · asks for confirmation before it runs · 2 inputs

Factory resets the device

Send

/system reset-configuration no-defaults={{NO_DEFAULTS}} skip-backup={{SKIP_BACKUP}}

Sends Enter afterwards.

MikroTik - Interfaces, Bridges & VLANs

29 buttons

List Interfaces

Run: /interface print detail

1 step

Send
```
/interface print detail
```
Sends Enter afterwards.

Show Interface Statistics

Run: /interface print stats

1 step

Send
```
/interface print stats
```
Sends Enter afterwards.

Monitor Interface Once

Run: /interface monitor-traffic {{INTERFACE}} once

1 step · 1 input

Send

/interface monitor-traffic {{INTERFACE}} once

Sends Enter afterwards.

Enable Interface

Run: /interface enable [find where name="{{INTERFACE}}"]

1 step · 1 input

Send

/interface enable [find where name="{{INTERFACE}}"]

Sends Enter afterwards.

Disable Interface

Run: /interface disable [find where name="{{INTERFACE}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/interface disable [find where name="{{INTERFACE}}"]

Sends Enter afterwards.

Set Interface Comment

Run: /interface set [find where name="{{INTERFACE}}"] comment="{{COMMENT}}"

1 step · 2 inputs

Send

/interface set [find where name="{{INTERFACE}}"] comment="{{COMMENT}}"

Sends Enter afterwards.

Rename Interface

Run: /interface set [find where name="{{INTERFACE}}"] name="{{NEW_NAME}}"

1 step · 2 inputs

Send

/interface set [find where name="{{INTERFACE}}"] name="{{NEW_NAME}}"

Sends Enter afterwards.

Set Interface MTU

Run: /interface set [find where name="{{INTERFACE}}"] mtu={{MTU}}

1 step · 2 inputs

Send

/interface set [find where name="{{INTERFACE}}"] mtu={{MTU}}

Sends Enter afterwards.

List Ethernet Interfaces

Run: /interface ethernet print detail

1 step

Send
```
/interface ethernet print detail
```
Sends Enter afterwards.

Monitor Ethernet Interface

Run: /interface ethernet monitor {{INTERFACE}} once

1 step · 1 input

Send

/interface ethernet monitor {{INTERFACE}} once

Sends Enter afterwards.

Set Ethernet Speed

Run: /interface ethernet set [find where name="{{INTERFACE}}"] auto-negotiation=no speed={{SPEED}}

1 step · 2 inputs

Send

/interface ethernet set [find where name="{{INTERFACE}}"] auto-negotiation=no speed={{SPEED}}

Sends Enter afterwards.

Enable Auto Negotiation

Run: /interface ethernet set [find where name="{{INTERFACE}}"] auto-negotiation=yes

1 step · 1 input

Send

/interface ethernet set [find where name="{{INTERFACE}}"] auto-negotiation=yes

Sends Enter afterwards.

List Bridges

Run: /interface bridge print detail

1 step

Send
```
/interface bridge print detail
```
Sends Enter afterwards.

Create Bridge

Run: /interface bridge add name="{{BRIDGE}}" protocol-mode={{PROTOCOL_MODE}} vlan-filtering={{VLAN_FILTERING}}

1 step · 3 inputs

Send

/interface bridge add name="{{BRIDGE}}" protocol-mode={{PROTOCOL_MODE}} vlan-filtering={{VLAN_FILTERING}}

Sends Enter afterwards.

Remove Bridge

Run: /interface bridge remove [find where name="{{BRIDGE}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/interface bridge remove [find where name="{{BRIDGE}}"]

Sends Enter afterwards.

List Bridge Ports

Run: /interface bridge port print detail

1 step

Send
```
/interface bridge port print detail
```
Sends Enter afterwards.

Add Bridge Port

Run: /interface bridge port add bridge="{{BRIDGE}}" interface="{{INTERFACE}}" pvid={{PVID}}

1 step · 3 inputs

Send

/interface bridge port add bridge="{{BRIDGE}}" interface="{{INTERFACE}}" pvid={{PVID}}

Sends Enter afterwards.

Remove Bridge Port

Run: /interface bridge port remove [find where bridge="{{BRIDGE}}" and interface="{{INTERFACE}}"]

1 step · asks for confirmation before it runs · 2 inputs

Send

/interface bridge port remove [find where bridge="{{BRIDGE}}" and interface="{{INTERFACE}}"]

Sends Enter afterwards.

Set Bridge Port PVID

Run: /interface bridge port set [find where bridge="{{BRIDGE}}" and interface="{{INTERFACE}}"] pvid={{PVID}}

1 step · 3 inputs

Send

/interface bridge port set [find where bridge="{{BRIDGE}}" and interface="{{INTERFACE}}"] pvid={{PVID}}

Sends Enter afterwards.

List Bridge VLANs

Run: /interface bridge vlan print detail

1 step

Send
```
/interface bridge vlan print detail
```
Sends Enter afterwards.

Add Bridge VLAN

Run: /interface bridge vlan add bridge="{{BRIDGE}}" vlan-ids={{VLAN_ID}} tagged="{{TAGGED}}" untagged="{{UNTAGGED}}"

1 step · 4 inputs

Send

/interface bridge vlan add bridge="{{BRIDGE}}" vlan-ids={{VLAN_ID}} tagged="{{TAGGED}}" untagged="{{UNTAGGED}}"

Sends Enter afterwards.

Remove Bridge VLAN

Run: /interface bridge vlan remove [find where bridge="{{BRIDGE}}" and vlan-ids={{VLAN_ID}}]

1 step · asks for confirmation before it runs · 2 inputs

Send

/interface bridge vlan remove [find where bridge="{{BRIDGE}}" and vlan-ids={{VLAN_ID}}]

Sends Enter afterwards.

Create VLAN Interface

Run: /interface vlan add name="{{VLAN_NAME}}" interface="{{INTERFACE}}" vlan-id={{VLAN_ID}}

1 step · 3 inputs

Send

/interface vlan add name="{{VLAN_NAME}}" interface="{{INTERFACE}}" vlan-id={{VLAN_ID}}

Sends Enter afterwards.

Remove VLAN Interface

Run: /interface vlan remove [find where name="{{VLAN_NAME}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/interface vlan remove [find where name="{{VLAN_NAME}}"]

Sends Enter afterwards.

List Bonding Interfaces

Run: /interface bonding print detail

1 step

Send
```
/interface bonding print detail
```
Sends Enter afterwards.

Create Bond

Run: /interface bonding add name="{{BOND}}" slaves="{{SLAVES}}" mode={{BOND_MODE}}

1 step · 3 inputs

Send

/interface bonding add name="{{BOND}}" slaves="{{SLAVES}}" mode={{BOND_MODE}}

Sends Enter afterwards.

Show Interface Lists

Run: /interface list print

1 step

Send
```
/interface list print
```
Sends Enter afterwards.

Add Interface List

Run: /interface list add name="{{LIST_NAME}}"

1 step · 1 input

Send

/interface list add name="{{LIST_NAME}}"

Sends Enter afterwards.

Add Interface to List

Run: /interface list member add list="{{LIST_NAME}}" interface="{{INTERFACE}}"

1 step · 2 inputs

Send

/interface list member add list="{{LIST_NAME}}" interface="{{INTERFACE}}"

Sends Enter afterwards.

MikroTik - IP Addresses, ARP & Neighbors

18 buttons

List IP Addresses

Run: /ip address print detail

1 step

Send
```
/ip address print detail
```
Sends Enter afterwards.

Add IP Address

Run: /ip address add address={{IP_CIDR}} interface="{{INTERFACE}}" comment="{{COMMENT}}"

1 step · 3 inputs

Send

/ip address add address={{IP_CIDR}} interface="{{INTERFACE}}" comment="{{COMMENT}}"

Sends Enter afterwards.

Disable IP Address

Run: /ip address disable [find where address="{{IP_CIDR}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/ip address disable [find where address="{{IP_CIDR}}"]

Sends Enter afterwards.

Enable IP Address

Run: /ip address enable [find where address="{{IP_CIDR}}"]

1 step · 1 input

Send

/ip address enable [find where address="{{IP_CIDR}}"]

Sends Enter afterwards.

Remove IP Address

Run: /ip address remove [find where address="{{IP_CIDR}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/ip address remove [find where address="{{IP_CIDR}}"]

Sends Enter afterwards.

List ARP Entries

Run: /ip arp print detail

1 step

Send
```
/ip arp print detail
```
Sends Enter afterwards.

Add Static ARP

Run: /ip arp add address={{IP_ADDRESS}} mac-address={{MAC_ADDRESS}} interface="{{INTERFACE}}"

1 step · 3 inputs

Send

/ip arp add address={{IP_ADDRESS}} mac-address={{MAC_ADDRESS}} interface="{{INTERFACE}}"

Sends Enter afterwards.

Remove ARP Entry

Run: /ip arp remove [find where address={{IP_ADDRESS}}]

1 step · asks for confirmation before it runs · 1 input

Send

/ip arp remove [find where address={{IP_ADDRESS}}]

Sends Enter afterwards.

List IPv6 Addresses

Run: /ipv6 address print detail

1 step

Send
```
/ipv6 address print detail
```
Sends Enter afterwards.

Add IPv6 Address

Run: /ipv6 address add address={{IPV6_CIDR}} interface="{{INTERFACE}}" advertise={{ADVERTISE}}

1 step · 3 inputs

Send

/ipv6 address add address={{IPV6_CIDR}} interface="{{INTERFACE}}" advertise={{ADVERTISE}}

Sends Enter afterwards.

Remove IPv6 Address

Run: /ipv6 address remove [find where address="{{IPV6_CIDR}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/ipv6 address remove [find where address="{{IPV6_CIDR}}"]

Sends Enter afterwards.

Show MikroTik Neighbors

Run: /ip neighbor print detail

1 step

Send
```
/ip neighbor print detail
```
Sends Enter afterwards.

Show MAC Neighbors

Run: /tool mac-scan interface="{{INTERFACE}}" duration={{DURATION}}

1 step · 2 inputs

Send

/tool mac-scan interface="{{INTERFACE}}" duration={{DURATION}}

Sends Enter afterwards.

Ping Host

Run: /ping {{HOST}} count={{COUNT}}

1 step · 2 inputs

Send
```
/ping {{HOST}} count={{COUNT}}
```
Sends Enter afterwards.

Ping from Source Address

Run: /ping {{HOST}} src-address={{SOURCE_IP}} count={{COUNT}}

1 step · 3 inputs

Send

/ping {{HOST}} src-address={{SOURCE_IP}} count={{COUNT}}

Sends Enter afterwards.

Ping via Interface

Run: /ping {{HOST}} interface="{{INTERFACE}}" count={{COUNT}}

1 step · 3 inputs

Send

/ping {{HOST}} interface="{{INTERFACE}}" count={{COUNT}}

Sends Enter afterwards.

Traceroute Host

Run: /tool traceroute {{HOST}}

1 step · 1 input

Send
```
/tool traceroute {{HOST}}
```
Sends Enter afterwards.

Traceroute Using Source

Run: /tool traceroute {{HOST}} src-address={{SOURCE_IP}}

1 step · 2 inputs

Send

/tool traceroute {{HOST}} src-address={{SOURCE_IP}}

Sends Enter afterwards.

MikroTik - Routing, BGP & OSPF

22 buttons

List IPv4 Routes

Run: /ip route print detail

1 step

Send
```
/ip route print detail
```
Sends Enter afterwards.

List Active Routes

Run: /ip route print where active

1 step

Send
```
/ip route print where active
```
Sends Enter afterwards.

Add Static Route

Run: /ip route add dst-address={{DESTINATION_CIDR}} gateway={{GATEWAY}} distance={{DISTANCE}} comment="{{COMMENT}}"

1 step · 4 inputs

Send

/ip route add dst-address={{DESTINATION_CIDR}} gateway={{GATEWAY}} distance={{DISTANCE}} comment="{{COMMENT}}"

Sends Enter afterwards.

Add Blackhole Route

Run: /ip route add dst-address={{DESTINATION_CIDR}} type=blackhole distance={{DISTANCE}} comment="{{COMMENT}}"

1 step · 3 inputs

Send

/ip route add dst-address={{DESTINATION_CIDR}} type=blackhole distance={{DISTANCE}} comment="{{COMMENT}}"

Sends Enter afterwards.

Disable Route

Run: /ip route disable [find where dst-address="{{DESTINATION_CIDR}}" and gateway="{{GATEWAY}}"]

1 step · asks for confirmation before it runs · 2 inputs

Send

/ip route disable [find where dst-address="{{DESTINATION_CIDR}}" and gateway="{{GATEWAY}}"]

Sends Enter afterwards.

Enable Route

Run: /ip route enable [find where dst-address="{{DESTINATION_CIDR}}" and gateway="{{GATEWAY}}"]

1 step · 2 inputs

Send

/ip route enable [find where dst-address="{{DESTINATION_CIDR}}" and gateway="{{GATEWAY}}"]

Sends Enter afterwards.

Remove Route

Run: /ip route remove [find where dst-address="{{DESTINATION_CIDR}}" and gateway="{{GATEWAY}}"]

1 step · asks for confirmation before it runs · 2 inputs

Send

/ip route remove [find where dst-address="{{DESTINATION_CIDR}}" and gateway="{{GATEWAY}}"]

Sends Enter afterwards.

List Route Rules

Run: /routing rule print detail

1 step

Send
```
/routing rule print detail
```
Sends Enter afterwards.

Add Route Rule

Run: /routing rule add src-address={{SOURCE_CIDR}} action=lookup table="{{ROUTING_TABLE}}"

1 step · 2 inputs

Send

/routing rule add src-address={{SOURCE_CIDR}} action=lookup table="{{ROUTING_TABLE}}"

Sends Enter afterwards.

List Routing Tables

Run: /routing table print detail

1 step

Send
```
/routing table print detail
```
Sends Enter afterwards.

Add Routing Table

Run: /routing table add name="{{ROUTING_TABLE}}" fib=yes

1 step · 1 input

Send

/routing table add name="{{ROUTING_TABLE}}" fib=yes

Sends Enter afterwards.

List BGP Connections

Run: /routing bgp connection print detail

1 step

Send
```
/routing bgp connection print detail
```
Sends Enter afterwards.

List BGP Sessions

Run: /routing bgp session print detail

1 step

Send
```
/routing bgp session print detail
```
Sends Enter afterwards.

Create BGP Template

Run: /routing bgp template add name="{{TEMPLATE}}" as={{LOCAL_AS}} router-id={{ROUTER_ID}}

1 step · 3 inputs

Send

/routing bgp template add name="{{TEMPLATE}}" as={{LOCAL_AS}} router-id={{ROUTER_ID}}

Sends Enter afterwards.

Create BGP Connection

Run: /routing bgp connection add name="{{BGP_NAME}}" remote.address={{REMOTE_ADDRESS}} remote.as={{REMOTE_AS}} local.role={{BGP_ROLE}} templates="{{TEMPLATE}}"

1 step · 5 inputs

Send

/routing bgp connection add name="{{BGP_NAME}}" remote.address={{REMOTE_ADDRESS}} remote.as={{REMOTE_AS}} local.role={{BGP_ROLE}} templates="{{TEMPLATE}}"

Sends Enter afterwards.

Disable BGP Connection

Run: /routing bgp connection disable [find where name="{{BGP_NAME}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/routing bgp connection disable [find where name="{{BGP_NAME}}"]

Sends Enter afterwards.

Enable BGP Connection

Run: /routing bgp connection enable [find where name="{{BGP_NAME}}"]

1 step · 1 input

Send

/routing bgp connection enable [find where name="{{BGP_NAME}}"]

Sends Enter afterwards.

List OSPF Instances

Run: /routing ospf instance print detail

1 step

Send
```
/routing ospf instance print detail
```
Sends Enter afterwards.

List OSPF Neighbors

Run: /routing ospf neighbor print detail

1 step

Send
```
/routing ospf neighbor print detail
```
Sends Enter afterwards.

List OSPF Interfaces

Run: /routing ospf interface-template print detail

1 step

Send

/routing ospf interface-template print detail

Sends Enter afterwards.

Add OSPF Interface Template

Run: /routing ospf interface-template add interfaces="{{INTERFACE}}" area="{{OSPF_AREA}}" networks={{NETWORK_CIDR}}

1 step · 3 inputs

Send

/routing ospf interface-template add interfaces="{{INTERFACE}}" area="{{OSPF_AREA}}" networks={{NETWORK_CIDR}}

Sends Enter afterwards.

List IPv6 Routes

Run: /ipv6 route print detail

1 step

Send
```
/ipv6 route print detail
```
Sends Enter afterwards.

MikroTik - Firewall, NAT & Address Lists

25 buttons

List Filter Rules

Run: /ip firewall filter print detail

1 step

Send
```
/ip firewall filter print detail
```
Sends Enter afterwards.

List Filter Rule Statistics

Run: /ip firewall filter print stats

1 step

Send
```
/ip firewall filter print stats
```
Sends Enter afterwards.

Add Accept Input Rule

Run: /ip firewall filter add chain=input action=accept protocol={{PROTOCOL}} dst-port={{PORT}} src-address={{SOURCE_CIDR}} comment="{{COMMENT}}"

1 step · 4 inputs

Send

/ip firewall filter add chain=input action=accept protocol={{PROTOCOL}} dst-port={{PORT}} src-address={{SOURCE_CIDR}} comment="{{COMMENT}}"

Sends Enter afterwards.

Add Drop Input Rule

Run: /ip firewall filter add chain=input action=drop src-address={{SOURCE_CIDR}} comment="{{COMMENT}}"

1 step · 2 inputs

Send

/ip firewall filter add chain=input action=drop src-address={{SOURCE_CIDR}} comment="{{COMMENT}}"

Sends Enter afterwards.

Add Established Related Rule

Run: /ip firewall filter add chain=input action=accept connection-state=established,related,untracked comment="Accept established and related"

1 step

Send

/ip firewall filter add chain=input action=accept connection-state=established,related,untracked comment="Accept established and related"

Sends Enter afterwards.

Disable Filter Rule by Comment

Run: /ip firewall filter disable [find where comment="{{COMMENT}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/ip firewall filter disable [find where comment="{{COMMENT}}"]

Sends Enter afterwards.

Enable Filter Rule by Comment

Run: /ip firewall filter enable [find where comment="{{COMMENT}}"]

1 step · 1 input

Send

/ip firewall filter enable [find where comment="{{COMMENT}}"]

Sends Enter afterwards.

Remove Filter Rule by Comment

Run: /ip firewall filter remove [find where comment="{{COMMENT}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/ip firewall filter remove [find where comment="{{COMMENT}}"]

Sends Enter afterwards.

Move Filter Rule

Run: /ip firewall filter move [find where comment="{{COMMENT}}"] destination={{POSITION}}

1 step · 2 inputs

Send

/ip firewall filter move [find where comment="{{COMMENT}}"] destination={{POSITION}}

Sends Enter afterwards.

List NAT Rules

Run: /ip firewall nat print detail

1 step

Send
```
/ip firewall nat print detail
```
Sends Enter afterwards.

Add Masquerade Rule

Run: /ip firewall nat add chain=srcnat action=masquerade out-interface="{{INTERFACE}}" comment="{{COMMENT}}"

1 step · 2 inputs

Send

/ip firewall nat add chain=srcnat action=masquerade out-interface="{{INTERFACE}}" comment="{{COMMENT}}"

Sends Enter afterwards.

Add Source NAT Rule

Run: /ip firewall nat add chain=srcnat action=src-nat src-address={{SOURCE_CIDR}} to-addresses={{TO_ADDRESS}} comment="{{COMMENT}}"

1 step · 3 inputs

Send

/ip firewall nat add chain=srcnat action=src-nat src-address={{SOURCE_CIDR}} to-addresses={{TO_ADDRESS}} comment="{{COMMENT}}"

Sends Enter afterwards.

Add Destination NAT Rule

Run: /ip firewall nat add chain=dstnat action=dst-nat protocol={{PROTOCOL}} dst-port={{PORT}} to-addresses={{TO_ADDRESS}} to-ports={{TO_PORT}} comment="{{COMMENT}}"

1 step · 5 inputs

Send

/ip firewall nat add chain=dstnat action=dst-nat protocol={{PROTOCOL}} dst-port={{PORT}} to-addresses={{TO_ADDRESS}} to-ports={{TO_PORT}} comment="{{COMMENT}}"

Sends Enter afterwards.

Disable NAT Rule by Comment

Run: /ip firewall nat disable [find where comment="{{COMMENT}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/ip firewall nat disable [find where comment="{{COMMENT}}"]

Sends Enter afterwards.

Enable NAT Rule by Comment

Run: /ip firewall nat enable [find where comment="{{COMMENT}}"]

1 step · 1 input

Send

/ip firewall nat enable [find where comment="{{COMMENT}}"]

Sends Enter afterwards.

Remove NAT Rule by Comment

Run: /ip firewall nat remove [find where comment="{{COMMENT}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/ip firewall nat remove [find where comment="{{COMMENT}}"]

Sends Enter afterwards.

List Mangle Rules

Run: /ip firewall mangle print detail

1 step

Send
```
/ip firewall mangle print detail
```
Sends Enter afterwards.

List Raw Rules

Run: /ip firewall raw print detail

1 step

Send
```
/ip firewall raw print detail
```
Sends Enter afterwards.

List Address Lists

Run: /ip firewall address-list print detail

1 step

Send
```
/ip firewall address-list print detail
```
Sends Enter afterwards.

Add Address List Entry

Run: /ip firewall address-list add list="{{ADDRESS_LIST}}" address={{IP_OR_CIDR}} timeout={{TIMEOUT}} comment="{{COMMENT}}"

1 step · 4 inputs

Send

/ip firewall address-list add list="{{ADDRESS_LIST}}" address={{IP_OR_CIDR}} timeout={{TIMEOUT}} comment="{{COMMENT}}"

Sends Enter afterwards.

Remove Address List Entry

Run: /ip firewall address-list remove [find where list="{{ADDRESS_LIST}}" and address="{{IP_OR_CIDR}}"]

1 step · asks for confirmation before it runs · 2 inputs

Send

/ip firewall address-list remove [find where list="{{ADDRESS_LIST}}" and address="{{IP_OR_CIDR}}"]

Sends Enter afterwards.

Flush Connection Tracking

Run: /ip firewall connection remove [find]

1 step · asks for confirmation before it runs

Send
```
/ip firewall connection remove [find]
```
Sends Enter afterwards.

List Connections

Run: /ip firewall connection print detail

1 step

Send
```
/ip firewall connection print detail
```
Sends Enter afterwards.

List IPv6 Filter Rules

Run: /ipv6 firewall filter print detail

1 step

Send
```
/ipv6 firewall filter print detail
```
Sends Enter afterwards.

Export Firewall Configuration

Run: /ip firewall export show-sensitive=no

1 step

Send
```
/ip firewall export show-sensitive=no
```
Sends Enter afterwards.

MikroTik - DHCP, DNS & Services

24 buttons

List DHCP Servers

Run: /ip dhcp-server print detail

1 step

Send
```
/ip dhcp-server print detail
```
Sends Enter afterwards.

List DHCP Leases

Run: /ip dhcp-server lease print detail

1 step

Send
```
/ip dhcp-server lease print detail
```
Sends Enter afterwards.

Show Bound DHCP Leases

Run: /ip dhcp-server lease print where status=bound

1 step

Send

/ip dhcp-server lease print where status=bound

Sends Enter afterwards.

Make DHCP Lease Static

Run: /ip dhcp-server lease make-static [find where address={{IP_ADDRESS}}]

1 step · 1 input

Send

/ip dhcp-server lease make-static [find where address={{IP_ADDRESS}}]

Sends Enter afterwards.

Add Static DHCP Lease

Run: /ip dhcp-server lease add server="{{DHCP_SERVER}}" address={{IP_ADDRESS}} mac-address={{MAC_ADDRESS}} comment="{{COMMENT}}"

1 step · 4 inputs

Send

/ip dhcp-server lease add server="{{DHCP_SERVER}}" address={{IP_ADDRESS}} mac-address={{MAC_ADDRESS}} comment="{{COMMENT}}"

Sends Enter afterwards.

Remove DHCP Lease

Run: /ip dhcp-server lease remove [find where address={{IP_ADDRESS}}]

1 step · asks for confirmation before it runs · 1 input

Send

/ip dhcp-server lease remove [find where address={{IP_ADDRESS}}]

Sends Enter afterwards.

Create DHCP Pool

Run: /ip pool add name="{{POOL_NAME}}" ranges={{IP_RANGE}}

1 step · 2 inputs

Send

/ip pool add name="{{POOL_NAME}}" ranges={{IP_RANGE}}

Sends Enter afterwards.

Create DHCP Network

Run: /ip dhcp-server network add address={{NETWORK_CIDR}} gateway={{GATEWAY}} dns-server={{DNS_SERVERS}} domain="{{DOMAIN}}"

1 step · 4 inputs

Send

/ip dhcp-server network add address={{NETWORK_CIDR}} gateway={{GATEWAY}} dns-server={{DNS_SERVERS}} domain="{{DOMAIN}}"

Sends Enter afterwards.

Create DHCP Server

Run: /ip dhcp-server add name="{{DHCP_SERVER}}" interface="{{INTERFACE}}" address-pool="{{POOL_NAME}}" disabled=no

1 step · 3 inputs

Send

/ip dhcp-server add name="{{DHCP_SERVER}}" interface="{{INTERFACE}}" address-pool="{{POOL_NAME}}" disabled=no

Sends Enter afterwards.

List DHCP Clients

Run: /ip dhcp-client print detail

1 step

Send
```
/ip dhcp-client print detail
```
Sends Enter afterwards.

Add DHCP Client

Run: /ip dhcp-client add interface="{{INTERFACE}}" add-default-route=yes use-peer-dns={{USE_PEER_DNS}} disabled=no

1 step · 2 inputs

Send

/ip dhcp-client add interface="{{INTERFACE}}" add-default-route=yes use-peer-dns={{USE_PEER_DNS}} disabled=no

Sends Enter afterwards.

Release DHCP Client

Run: /ip dhcp-client release [find where interface="{{INTERFACE}}"]

1 step · 1 input

Send

/ip dhcp-client release [find where interface="{{INTERFACE}}"]

Sends Enter afterwards.

Renew DHCP Client

Run: /ip dhcp-client renew [find where interface="{{INTERFACE}}"]

1 step · 1 input

Send

/ip dhcp-client renew [find where interface="{{INTERFACE}}"]

Sends Enter afterwards.

Show DNS Settings

Run: /ip dns print

1 step

Send
```
/ip dns print
```
Sends Enter afterwards.

Set DNS Servers

Run: /ip dns set servers={{DNS_SERVERS}} allow-remote-requests={{ALLOW_REMOTE}}

1 step · 2 inputs

Send

/ip dns set servers={{DNS_SERVERS}} allow-remote-requests={{ALLOW_REMOTE}}

Sends Enter afterwards.

List DNS Cache

Run: /ip dns cache print

1 step

Send
```
/ip dns cache print
```
Sends Enter afterwards.

Flush DNS Cache

Run: /ip dns cache flush

1 step

Send
```
/ip dns cache flush
```
Sends Enter afterwards.

Add Static DNS Record

Run: /ip dns static add name="{{DNS_NAME}}" address={{IP_ADDRESS}} ttl={{TTL}}

1 step · 3 inputs

Send

/ip dns static add name="{{DNS_NAME}}" address={{IP_ADDRESS}} ttl={{TTL}}

Sends Enter afterwards.

Remove Static DNS Record

Run: /ip dns static remove [find where name="{{DNS_NAME}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/ip dns static remove [find where name="{{DNS_NAME}}"]

Sends Enter afterwards.

List IP Services

Run: /ip service print detail

1 step

Send
```
/ip service print detail
```
Sends Enter afterwards.

Set SSH Allowed Address

Run: /ip service set ssh address={{ALLOWED_CIDR}} port={{PORT}} disabled=no

1 step · 2 inputs

Send

/ip service set ssh address={{ALLOWED_CIDR}} port={{PORT}} disabled=no

Sends Enter afterwards.

Disable IP Service

Run: /ip service disable [find where name="{{SERVICE}}"]

1 step · asks for confirmation before it runs · 1 input

Send

/ip service disable [find where name="{{SERVICE}}"]

Sends Enter afterwards.

Enable IP Service

Run: /ip service enable [find where name="{{SERVICE}}"]

1 step · 1 input

Send

/ip service enable [find where name="{{SERVICE}}"]

Sends Enter afterwards.

Set Service Port

Run: /ip service set [find where name="{{SERVICE}}"] port={{PORT}}

1 step · 2 inputs

Send

/ip service set [find where name="{{SERVICE}}"] port={{PORT}}

Sends Enter afterwards.

Version history

Revision 1 current

First published version.

13 Aug 2026 · 143.9 KB · needs 1.0.0+ · 89a37bcb97eaf9b9…

View Download